DvbDream Community

and i have it hooked up to a dish1000 with the just the one dishpro echostar 119west lnbf.

lnb type na bandstacked dishpro ku-hi dbs diseqc port1
for echostar 10, 11 110west.

it says good singal over80, and q over 90.

i do a scan and it says "no singal"

i think i got a bad genpix skywalker2, and would like to exchange it for a new one with the PCI card bracket standard size

you said:

Why do you configure DVB Dream to use sat 110 then:

i the dish1000.2 supports 3 satllite's. 129west, ecostar 119west , echostar 119west.


And why do you configure software to use diseqc switch if you don't have switch in the system?


Who says?
You have to get a lock to the signal before program can show any signal strength.some one gave me a channel list for a dish1000.2.
i treid a free channel like nasa.

And since you do have a signal strength.
The following statement contradicts to your statement above:



PS: Dish 1000 is not a description of your setup. It's meraly a description of the reflector (you said nothing about LNBs). And since you said that you have just one LNB, it is NOT standard Dish 1000 configuration. You have to provide details. How many LNBs are on your dish? do you know the difference between Dual and Twin LNB?

it's a dish1000.2 old type, the very 1st one dn came out with.

"do you know the the difference between Dual and Twin LNB?"
yes i do.

"in case you incorrectly described your setup, and you have Three LNBs on your dish with built-in DPP switch, please tell what power supply do you use to power this power-hungry monster. SkyWalker-2 may not be enough to provide enough power (it can power DPP Twin, but DPP Triple-LNB assembly is a stretch)

"you do know that hot-plugging of coax-cables can kill a receiver or DVB-s card, don't you?"

yes i do. thats why i plugin the cable when the pc is off!!!!

"Also, do you know how to ground an antenna (what is CORRECT grounding?)?"

i had my dish1000.1 installed by a dishnetwork installer.so i know the ground is good.it's a long green copper wire hooked to a steal pole in the ground.

"Do you know how to aim dish?" like i said above a dishnetork installer install the dish for satllite's 129west, 119west, 110west dishnetwork satllites.

"Do you know how to interconnect receivers and LNBs (you need switches)?"

"Do you know that you can NOT use cable splitters with satellite equipment?" i never used any "splitters with satellite equipment"!never will.don't trust them.

"Do you know that you can not use mechanical A-B switches with satellite equipment?"yes. i do know ...

"I'm asking this because it seems like you don't know how to replace PCI bracket on the PCI card. (SkyWalker-2 comes with low-profile PCI bracket installed, and spare full size PCI bracket in the same bag as internal USB cable)."i replaced the PCI bracket on the PCI card when i got the genpix skywalker-2 card.

meaning if i need to exchange it for one more genpix skywalker-2 card,
that i need one with the old type of PCI bracket on the pci card.

not the "small PCI bracket" that comes installed onto the genpix skywalker-2 card.

i have built pc's since 1998.
i have been into fta hobby since 2005.

You wrote me in e-mail:

All you need is a phillips screw-driver (philips screw driver is the one with a cross at the end), undo the screws, align a full size PCI bracket with mounting holes, and put the same two screws back.

i had my dish1000.1 installed by a dishnetwork installer.so i know the ground is good.it's a long green copper wire hooked to a steal pole in the ground.

"Sorry, but this is NOT a description of proper grounding.
It does sound like a description of INCORRECT grounding.

looks like i wasted my $203 usa on a device that never worked right!!

first of all, DishNetwork does not install dishes.
Contractors do (and they put whatever label they want on their vans; but it does NOT mean that they are DishNetwork company).

Unfortunately, many contractors do cut the cost of installation (and don't do a proper job).

Read this about grounding (especially the part "Never allow your installer to ..." - these are the first two paragraphs):
h++p://www.dbsinstall.com/whatis/Whatisgood-5.asp
as well as entire Grounding section in DIY area:
h++p://www.dbsinstall.com/diy/diy.asp"

well i checked it out and looked at my grounding system, and it looks good to me.if you don't beleave me i can easy put a picture of my the outside wall of my house of the grounding system.


This is just to refresh your memory,
cause you had to know that long ago (since you are into this hobby since 2005).

one more thing:
You paid less then $200, didn't you?

I received your SkyWalker-2 back.
All I can say: it's working fine here. There are absolutely no problems with it.

Instead of sending me e-mails (over and over again) that your dish is "professionally installed", why can't you simply describe HOW it is grounded?
Or you have no clue how it is actually done?
Can't you walk outside your house and trace where grounding wires are going?

"Can't you walk outside your house and trace where grounding wires are going?"

did that and it looks good like i said.

it's a long green copper wire hooked to a steal pole in the ground.

"what motherboard do you have (manufacturer, model name/number)?"

it's a compaq 6zpxe32

does it have USB 2.0 ports? yes it has one usb2.0 on the mainboard

What's the BIOS version (number and date)?3.06 (11/21/02) A

Is it latest BIOS version?yes, it is up to date.

i have installed usb2.0 support for the compaq 6zpx32 mainboard.
for xp.

added:
based on your CPU/GPU spec, I think you don't have enough horsepower to tune to h.264 channels. MPEG-2 is your only option for now (i'm not sure about mpeg-2 HD, your machine may be just barely enough for that).

you may get away with newer Video card (which has hardware support for h.264; don't go for fast 3D card, simple card with hardware h.264 support is what you need).

You may download h.264 clips from internet, and see how fast/slow your system is."
besides i am going to use it in my dad's dual core amd vista pc,
it is less than a year old, with a 4GB of ram.a new geforce hd card.that he it has usb2.0 , he got it ayear ago.

i am going to upgrade to a new mainboard next month, can't right now i am really low on cash, after buying that skywalker-2.

good free clips (different resolution) are here:
h++p://www.apple.com/quicktime/guide/hd/
h++p://www.h264info.com/clips.html