Err...Proof? No, I am glad that you have managed to get your setup to work: tu es muy macho. What we are all here interested in in is HOW you did it... E.g., what are all of your DiSeqc settings, please? I think he is talking about the 1025 and not the 1027. The two are different animals. The 1027 ...

I tried it with the twinhan 1027 and it did not work with disesq. It did seem to be more stable than the old version though. I was able to click close and the program shut down. That's a first.

DD will not shut down when the X is clicked to close it, but it will continue to run normally. Sometimes it will eventually shut down by itself in about 10 minutes. Sometimes you can go into the task manager and manually shut it down, but sometimes it wont let you do that either. Usually when the la...

Has anybody tried this? Connect a 22 KHz switch to the two sat ports on the DP500 LNB and use it instead of the internal disecq switch to switch between sats. A 22KHz switch has a much simpler protocol over diseqc switches. On a single receiver setup, it might be a workaround for the diseqc problem ...

Is this what you want: [05/18/08 08:25:34 : ] >> DeviceGetList [05/18/08 08:25:34 : 16] Tuner Type (Detected) : DVB-S [05/18/08 08:25:34 : 31] - Filter [DTV-DVB 1027 DVBS BDA Tuner Filter] TunerType:1 [05/18/08 08:25:34 : 31] << DeviceGetList [05/18/08 08:25:34 : 31] StartDevice() dwDeviceNo:0 [05/1...

Yes, that is pretty much how I did it. You tune the STB on whatever sat you want and that will be the one that gets passed out the LOOP OUT connector. Since I'm using dishpro, I don't have to worry about polarity.

Hi Rel,

Here is a photo pf the 1027 if it helps develop a driver to make it work with DISEQC.

Wondering the same thing myself. A lot of people use the 1027. I have resorted to using an STB to do the diseqc switching.

Why are you using a mantis driver with a 1027 card? I didn't think the 1027 was mantis.

2) E0 10 38 F0 (port 1) E0 10 38 F4 (port 2) E0 10 38 F8 (port 3) E0 10 38 FC (port 4) According to the Diseqc specs, the following are the proper codes: E0 10 38 F1 (port 1) E0 10 38 F2 (port 2) E0 10 38 F4 (port 3) E0 10 38 F8 (port 4) Nevertheless, they still don't work with a 1027. Also, you ne...

Thats because Vista+ Notepad = 100%

Install XP and you'll run about twice as fast.

I had the same problem with Intervideo codec version 5.0. It worked really great for about a month. In fact, it works better than any codec out there for mpeg2. I could have 10 pips open with only about 90% cpu. With FFDshow, I can only get about 3 or 4 at 90%. But in the end, FFDShow wins because i...

I got a similar problem. The video played back with no sound and at twice normal speed. This may be a codec issue.

I have a similar problem with the Twinhan 1027. I have never found the cause or a good solution to the zero signal strength problem in DD. However, I have found a few possible workarounds. First, try this, go to the Devices and restart the device by highlighting it and then clicking START and then O...

They have manual switches that you can use. You don't want to continually be disconnecting and reconnecting cables. They wont hold up. Alternatively, you could try using Mytheater. Its not freeware, but it will let you watch for an hour at a time before it shuts down. It supports the 1027 and probab...