DvbDream Community

Love the collapsable gui main window stuff, very nice.
Thanks for positioner set on program start. Been wishing for that for many versions.

Positioner window elements a bit off, graphic at top is covering up title bar slightly (certainly no big deal).

For some reason (on a couple versions now) program start up the first time crashes on DVBEPG ini allegedly out of date. Gotta delete it and rebuild it, wierd, but no big deal.

Nice work, thanks, you are appreciated.

Thanks for positioner set on program start. Been wishing for that for many versions.

did it work ? lol (couldn't test it here.)

thanks for the comments

Upon further testing, yes and no. The positioner is moving, but I think the diseqc switch is not getting set. Bring up MT on E7 which is on port 1 and shut it down. Start DD on E5 which is on port 2, positioner moves but no signal, change channels and signal pops right in. I have 2 lnb's, 1 Invacomp that does both linear and circular on seperate outputs, and a second lnb hanging off to the side so I can do both E7&8 and N1&2 without having to move the dish.

As i am testing further, boy if this isn't bad timing. My motor is crapped out. Going up to the dish and pushing bottons to do this manualy, it moves west fine. Going east it just grinds to halt and quits. Second motor to crap out this year.

Maybe the program is fine and my initial trouble was just before it crapped out. More data when I can move me motor properly.

- 1.4d persistently crashes with FFDShow 2007-11-10 (audio and wideo) when I switch up a canal.
- biger cpu ussage 60÷70%, 1,4c was max 40%

1stly thanks to Rel for his work and for the other members those helped him

after updated vesion of installation of it over the 1.4c many cashes happened and uninstallation and reinstallation done few cashes more on switching channels from H to V
uninstallation and reinstallation after cleaning prefetch folder
finally it works stable now with diseqc 1 with 2 satellites and no motor

works stable now with FFdshow xxl version by date 26-10-07 for video and New Nvidia audio and VMR.

Thanks again guys

Thanks REL,but I have many dropped frames at VMR9 at 1.4(all versions) ...I changed video,audio codec but still....

Thanks REL,but I have many dropped frames at VMR9 at 1.4(all versions) ...I changed video,audio codec but still....

Try FFdshow with enabling "queuqe enabled" and enable queue in VMR9 and inYV12 and add dvbdream.exe programs that utilize it, assuming that you have dual core cpu or hyperthreading cpu.

By the way why you waste cpu power with using VMR9?
What you gain from it?

VMR is fair enough

Regards

- 1.4d persistently crashes with FFDShow 2007-11-10 (audio and wideo) when I switch up a canal.
- biger cpu ussage 60÷70%, 1,4c was max 40%

try disabling log file (options->preferences->general) I don't think FFDShow is a good choice for stable work.

By the way why you waste cpu power with using VMR9?
What you gain from it?

With some graphic cards and compatible codecs, it uses GPU power, not CPU. VMR9 would work better and could consume less CPU with new graphic cards, if codecs support hardware acceleration - DXVA .

Thanks REL when I was disabled "log file" CPU ussage is only 20÷30% , now I use Cyberlink Video + FFDShow audio and it appears to be stable.

Thanks for positioner set on program start. Been wishing for that for many versions.

did it work ? lol (couldn't test it here.)

thanks for the comments

new motor, positioner and diseqc set fine on startup. Thanks

New motor gives an opportunity to point out that the positioner control locks up the program quite regularly. Any ideas?

When recording on I see at OSD only time.Before I see time and size at MB...

Before 00:01:05 - 15MB

Now only 00:01:05

I use OSD 1.22,DD 1.4d

DVB Dream forum rules:

Create one thread per bug/feature request, instead of collecting them in a post!

I can't even get VMR9 to work at all. I just use the VMR and it works fine. I tried all the possible combos to get VMR9 going and no luck. FDSHOW was the same. By the way is it better to lower the resolution when plugged into a HDTV using a DVI-HDMI cable? The quality of the video isn't so great but it's AMAZING for the text coming out of my pc.

Thanks REL,but I have many dropped frames at VMR9 at 1.4(all versions) ...I changed video,audio codec but still....