DvbDream Community

Hey

been using dvbdream for years and it's the best viewer for dvb that i've tried .. but i have one problem, it usually will not record the Dolby-E pid even tho i have set it to record all pids etc in settings .. is there a way to make it record all pids even those it does not recognize?

Regards
MrC

If there was some event feed that used Dolby-E I used my TSwriter2 module.. however I probably need to add mode to allow dialog to be closed while recording.
Does it show an audio type in the audio pid editor? Possible to fake the audio type? Can you listen to Dolby-E audio in realtime?

nah there is no pid recognized in the channel properties, no i have no way of listening to it in real time, i like to record it and reencode it to DTS HD afterwards tho

maybe you can send me a sample stream and we can fix the problem by making DD recognize unknown audio pid format.

Normally if it had recognized the pid, you could pick TS as record format. then pick "All audio pids" in "Preferences->Record->TS Records", it would finely record the audio.


Can you upload some sample stream from that transponder for me to test?

How to capture a sample stream
1) Depending on the device you got there, you might first need to enable "Full TS" mode in device options & restart DD
2) start "TSWriter" (or "Stream Recorder") module on the problematic transponder, record about 100 mb
3) upload file to somewhere (Hotfile, Rapidshare). and send links to me

it was a Biss encoded stream that contains h264 4.2.2 video 1 mp2 track and 1 dolby e track

recorded with transedit and decrypted via tsdec. ffmpeg sees it as an unknown track, tsmuxer cant detect it but good luck with it.

it must be possible to record and extract it correctly some how as there are a few streams out there that have been converted to dts to take advange of the higher quilty dolby e audio.


http://speedy.sh/Ft4PX/dole.ts

maybe you can send me a sample stream and we can fix the problem by making DD recognize unknown audio pid format.

Normally if it had recognized the pid, you could pick TS as record format. then pick "All audio pids" in "Preferences->Record->TS Records", it would finely record the audio.


Can you upload some sample stream from that transponder for me to test?

How to capture a sample stream
1) Depending on the device you got there, you might first need to enable "Full TS" mode in device options & restart DD
2) start "TSWriter" (or "Stream Recorder") module on the problematic transponder, record about 100 mb
3) upload file to somewhere (Hotfile, Rapidshare). and send links to me

thanks for taking the time to look into this i see a sample was allready provided (alltho it doesn't look correct in transedit, should say AES3 PCM Audio on dolby pid) but here is another one. (was recored on my dreambox but the entire transponder is there)

http://www.speedyshare.com/z7TJp/201202 ... 4-02-48.ts

feedfreak u prolly found my caps, if i want dolby-e i also use transedit to cap and convert with dts encoder ... but would ofc like it to be able to record dolby pid in dvbdream

maybe you can send me a sample stream and we can fix the problem by making DD recognize unknown audio pid format.

Normally if it had recognized the pid, you could pick TS as record format. then pick "All audio pids" in "Preferences->Record->TS Records", it would finely record the audio.


Can you upload some sample stream from that transponder for me to test?

How to capture a sample stream
1) Depending on the device you got there, you might first need to enable "Full TS" mode in device options & restart DD
2) start "TSWriter" (or "Stream Recorder") module on the problematic transponder, record about 100 mb
3) upload file to somewhere (Hotfile, Rapidshare). and send links to me

thanks for taking the time to look into this i see a sample was allready provided (alltho it doesn't look correct in transedit, should say AES3 PCM Audio on dolby pid) but here is another one. (was recored on my dreambox but the entire transponder is there)

http://www.speedyshare.com/z7TJp/201202 ... 4-02-48.ts

feedfreak u prolly found my caps, if i want dolby-e i also use transedit to cap and convert with dts encoder ... but would ofc like it to be able to record dolby pid in dvbdream

maybe ts dec messed it up when removing the encrytion, i always record the video, mp2/ac3 track and aes pcm track (dolby e) with transedit. Have you experimented with encrypted files or just FTA?

edit - needed to record the pat with the streams so they are all detected correctly dolby e is now detected before and after decrytion. Would be cool if DvbDream could implement the doby e pid recording to enabe watching the channle live while recording

oh i see, yes i always cap entire stream inc pat so that could be it.

We will check it soon, at least to make DD recognize the pid , even though it probably won't be able to play it.

no, i don't think there is any free or pay codec avalible for dolby-e yet, maybe there never will be but u can always hope

no, i don't think there is any free or pay codec avalible for dolby-e yet, maybe there never will be but u can always hope

think the guy responsible for ffmpeg has it done but is holding out for $