8in/1out switch with diseqc 1.2

[vladomir]

Hello, I have SS2 and "centauri S168" 8in/1out switch to run more than 4 satelites, but this switch supports only diseq 1.1 and 1.2 and dvb dream supports diseqc 2.0 and raw diseqc. Is it possible to run dvb dream with patched SS2 driver using the raw diseqc? As I know it is possible to use the 1.2 diseqc on prog dvb, but I like much more dvb dream, thank you.

🌟 Recommended Tools & Services

• Formify.one - Free Online Form Creator (Better than Google Forms). - Create Professional Forms That Match Your Business, Form Builder That Actually Helps You Collect More Responses
• CrispShare - Screenshot Editor That Makes Your Work Look Professional (Without Design Skills). - Make Your Screenshots Stand Out in Crowded Social Feeds
• DVB Dream - Best TV Reception/Record software for your computer DVB add on. - Stop Missing Your Favorite Shows - Record TV Directly to Your PC. Turn Your Computer Into a Professional TV Recorder. Unlock Its Full Potential With Professional TV Software

[jerryt]

That switch has a committed 4x1 diseqc switch internally cascaded to four uncommitted 2x1 diseqc switches.

Should be able to just enter in the raw commands for that type of switch set up and you are done.

You should have all the raw commands you need here;
Committed lnb1 raw command E0 10 38 F0
Committed lnb2 raw command E0 10 38 F4
Committed lnb3 raw command E0 10 38 F8
Committed lnb4 raw command E0 10 38 FC
Uncommitted lnb1 raw command E0 10 39 F0
Uncommitted lnb2 raw command E0 10 39 F1

Should look like this;
E0 10 38 F0 E0 10 39 F0
for Committed port 1 (or A) Uncommitted port 1(or A)

The switch label has the port markings Uncommitted and Committed.

[vladomir]

thank you, it works

[elzipa]

Hi I tried doing the set up mentioned above but did no get good results; obviously I am doing something wrong and I need some help.

- Do I need to input any data on the type of LNB I did in my case Ku Circular?
- Do I need to do anything in the Uncommitted tab there are numbers from 0 till 10 or so or do not touch it at all?
- In the raw command for each LNB do I input only the number i.e. ( E0 10 38 F0 ) and the next for following one?
- This is what I trying but no go: this is for 8 LNBs added?

Committed lnb1 raw command => E0 10 38 F0
Committed lnb2 raw command => E0 10 38 F4
Committed lnb3 raw command => E0 10 38 F8
Committed lnb4 raw command => E0 10 38 FC
Uncommitted lnb1 raw command => E0 10 39 F0
Uncommitted lnb2 raw command => E0 10 39 F1
Uncommitted lnb3 raw command => E0 10 39 F2
Uncommitted lnb4 raw command => E0 10 39 F3

[elzipa]

I got it working now... You will have to use either all commited commands or all uncommitted commands... Second post was misleading!

[Dodge]

Please let us know in detail how you did it! (Please answer your own questions)
Also, please include any settings in the 22kHz tab?
Thank you


quote="elzipa"]Hi I tried doing the set up mentioned above but did no get good results; obviously I am doing something wrong and I need some help.

- Do I need to input any data on the type of LNB I did in my case Ku Circular?
- Do I need to do anything in the Uncommitted tab there are numbers from 0 till 10 or so or do not touch it at all?
- In the raw command for each LNB do I input only the number i.e. ( E0 10 38 F0 ) and the next for following one?
- This is what I trying but no go: this is for 8 LNBs added?

Committed lnb1 raw command => E0 10 38 F0
Committed lnb2 raw command => E0 10 38 F4
Committed lnb3 raw command => E0 10 38 F8
Committed lnb4 raw command => E0 10 38 FC
Uncommitted lnb1 raw command => E0 10 39 F0
Uncommitted lnb2 raw command => E0 10 39 F1
Uncommitted lnb3 raw command => E0 10 39 F2
Uncommitted lnb4 raw command => E0 10 39 F3[/quote]

[jerryt]

Hello, I have SS2 and "centauri S168" 8in/1out switch

Second post is for the Centauri S168 switch, which has both committed and uncommitted in one switch.

There is a new 8X1 switch by Digiwave, that has eight uncommitted ports. (The digiwave switch can be cascaded in front of 4X1 committed switches for 32 LNBs).

[Dodge]

There is a new 8X1 switch by Digiwave, that has eight uncommitted ports. (The digiwave switch can be cascaded in front of 4X1 committed switches for 32 LNBs).[/quote]
--------------------------------------------------------------------------

I bought the following 8 x1 switch off e-bay and cannot make it work with DVBdream. May be jerry or someone else has some advice.

The switch plate: GD-81A Multiprotocol programmable DISEqC switch
8 in 1 DISEqC 1.1

I think I tried using all possible DISEqC settings in the DREAM diseqC menu. Port one is usable, but none of the other 7 ports seem to pass a signal, no matter what the settings are.

What should be the settings in DREAM ????

DiseqC Switch Type: NONE, MINI, DISqC v. 1.0 or2.0 ????????

Port 1 Properties ???????? ( on my 8x1 Switch is E6)
Port 2 ( on my 8x1 SW it's E7)
Port 3
Port 4 ?????????

LOF 1 11250000 LNB Type : NA Legacy

Raw Diseqc Tab
E0 10 39 F0 (used for LNB 1)

22 kHz Tab ????? controlled by LOF Sw ON Off ?????

Uncommitted Port Switch: Disabled 0 , 1, 2,......... ?????


How do I find the right settings for this switch? Unfortunately there were no instructions in the box.

Thanks for any help

[jerryt]

Uncommitted CMD 0 raw command E0 10 39 F0
Uncommitted CMD 1 raw command E0 10 39 F1
Uncommitted CMD 2 raw command E0 10 39 F2
Uncommitted CMD 3 raw command E0 10 39 F3
Uncommitted CMD 4 raw command E0 10 39 F4
Uncommitted CMD 5 raw command E0 10 39 F5
Uncommitted CMD 6 raw command E0 10 39 F6
Uncommitted CMD 7 raw command E0 10 39 F7

[Professore]

Hello i have an Wave Frontier T90. I have set up until now 5 sattelites and i will add another 3. I have and also an "Profi-LINE EMP- Cetauri P-168 v2 8-1" and a TT-S2 3200 pci card. Can i use with DreamDVB all 8 ports? How i am going to do that?

[Professore]

nobody? i have downloaded the patched bda driver (from here: http://www.dvbdream.org/forum/viewtopic ... c&start=15) but still nothing..

[Raeesi]

Hi
i know this is a old topic but i have same problem & i dont know what should i do exactly!
My DVB Card is Technisat SkyStar USB HD
My DiseqC Switch is this: http://www.aoun-technologies.com/produc ... qc109w.php
now i dont know how & where should i set these commands in my DD!
I've tried in setting. i selected None for switch type then i've added my satellites & after that went to setting of each sat & then entered E0 10 39 F0 fot my 1st LNB then E0 10 39 F1 for 2nd & did others like this but after that when i tried to scan, nothing happens!

[rel]

Hi
i know this is a old topic but i have same problem & i dont know what should i do exactly!
My DVB Card is Technisat SkyStar USB HD
My DiseqC Switch is this: http://www.aoun-technologies.com/produc ... qc109w.php
now i dont know how & where should i set these commands in my DD!
I've tried in setting. i selected None for switch type then i've added my satellites & after that went to setting of each sat & then entered E0 10 39 F0 fot my 1st LNB then E0 10 39 F1 for 2nd & did others like this but after that when i tried to scan, nothing happens!

Did you try uncommitted switch setings? There is a tab when you add satellites, in that dialog. select None as diseqc switch type, then assign different uncommitted port numbers to each satellite you add.